1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

No Internet On main computer

Discussion in 'Hardware' started by star393, Feb 11, 2011.

Thread Status:
Not open for further replies.
  1. star393

    star393 Private E-2

    Windows XP Pro comcast cable modem linksys router ,

    Hard wired systems not using wyfi ,my main computer got wacked somehow as it was the only computer on at the time thur router another computer works fine which was off at the time.

    Problem is since jan 30 2011 i cannot for the life on me get this computer back on line. went through all i kmow how to do and yet windows willnot allow a ip address to get on line. I cannot ping anything and ipconfig willnot show a mac or ip address router is delivering one but windows keeps telling me contact your network person. under repair network willnot conect all other tests pass. proper boxes are checked in devices and comcast as no other advise for4 me. We went thur the deal 4 times together. Plugging cable modem directly into said computer willnot offer any diff. out comes.
    Using windows defender but turn off and no other firewall. Did have Noprton but uninstalled it,no changes. Reloaded devices and connections wizARD MANY TIMES no luck. Tried aux network card same deal no luck. Ran malware and regisry software and trojant finder no luck. ip router enabled no wins proxy enabled no net bois over tcpip disabled .
    Looked into log and found Failed to load net bios and netBT Tried net bois over tcpip box but that didnot work either. The three devices are in windows/system32/devices afd.sys tcpip.sys net bt.sys I did abunch of other stuff trying to keep a log of what i did. Still pulling the hair out of my head any thoughts or help would be greatly appreciated. Iam a hargware person from dos 3 still have all my junk around 200 baud modem for sale LMAo
    how about a big 1 meg harddrive dam aim old. No cherry but this software stuff pulls my hair out. Just no time to read alot. Thanks ahead of time

    star393@juno.com www.FriedbergRacing.com Douglas aka Star393
     
  2. star393

    star393 Private E-2

    Also i wanta add that in the begining everytime i clicked on a device in system devices it would disappear. screwy.
     
  3. handygal

    handygal Sergeant Major

    Was there something going on weather or electrical at the time? It could be that your network card is damaged. It sounds a lot like it was. It used to happen more often, I had a stash of extras for a while.

    You could try a new network card or a wireless one. I like a simple USB wireless, installs quickly, less chance of someone doing something wrong when the case stays closed too.
     
  4. star393

    star393 Private E-2

    Did that already with installing another network card same deal No electrical problems accurred. Electrical system is protected from computers. And i do have a 11,000 rpm BBC darg Race car
     
  5. star393

    star393 Private E-2

    i ran at the run box cmd/k sc qc dhcp and nothing other then black box with documents and settings adm showed up no info . I hate to have to reinstall wins again for the 100th time, i like to know what goes wrong. I guess i like pain.
     
  6. star393

    star393 Private E-2

    Back in the day when 250 MB hard drives were it i used to take them apart and change the bearings and repair the ribbon on the heads common failure causes, not today hard drives are like old shoes replace em. but still today it pays to pull your covers blow out the dirt from power supply,check the fans and most importantly look at all your capacitors on the mother board, at the tops and see if there expanding from age and just cheap caps. You can replace them before your system IDE goes bad and then your in trouble. There cheap and easy to do if you have some talent. But do watch them and head off problems or just replace your M/B , before your pulling your hair out too.
     
  7. handygal

    handygal Sergeant Major

    Forgive all of the questions, I'm trying to get the picture so I don't ask you things that you've already done.

    Do you show a network card in the Device manager (the one in control panel, i'm not good with the file)? Does it show the right model? It's not asking for a driver in the device manager?

    When you run ipconfig does it show Ethernet Adapter Network Area Connection and then just no MAC or ip under it or does it not even list that line?

    I usually want to know why and how and fix the problem rather than a work around. Sometimes it's not worth my sanity. I'd hit a box store, try a usb wireless as a work around, if it doesn't work you can take it back.

    Netbios over tcp/ip does need to be enabled but you tried that and other than that, nothing obvious in the config yet because it seems like maybe it's not even reading the card properly.

    I so hate reloading the OS that I've done it only twice. Maybe not smart, but i'll work on a fix for weeks rather than reload. I adminster 50+ computers, surely i've needed to reinstall the OS more than that. Just hearing reformat, install the OS makes me shudder. You'll never get that as a suggestion from me.
     
  8. lbmest

    lbmest MajorGeek

  9. star393

    star393 Private E-2

    Hello again thanks for repleys

    Yes network card is in device manager and correct devices drivers, and is enabled and running. I reloaded it several times and reloaded it in save mode also. Iam not sure if ipconfig shows card ,but ill check later today. Remember i also installed another network card and used that and still had same problems.So i went back to oem on board network adapter.
     
  10. star393

    star393 Private E-2

    No i did not try that but i will and get back to you. thanks for the link sent to the printer T/Y. Lol maybe with enough time to read all this stuff i might get done reading about windows 3.0 lmao.
     
  11. star393

    star393 Private E-2

    it seems that i cannot run this command from windows xp professional when i type netsh at command promt it changes dir to it but no info.
     
  12. star393

    star393 Private E-2



    YES the network card is listed in the ipconfig/all command
     
  13. handygal

    handygal Sergeant Major

    I was looking through my settings and amend my previous statemetn, netbios needs to be enabled if you use static ip's. I generally do so that sticks with me.

    Are you static or DHCP?

    The netbios error in the log concerns me. Is there more info on it? I'd like to make sure that isn't the source. I'd like to try to get my XP machine set the way yorus is and see if the netbios would keep me from connecting. If it is netbios we could focus on that.

    Here's my ipconfig /all can you tell my what is different in yours? (if you are static, I'll change mine over)


    Windows IP Configuration

    Host Name . . . . . . . . . . . . : D444CS
    Primary Dns Suffix . . . . . . . :
    Node Type . . . . . . . . . . . . : Broadcast
    IP Routing Enabled. . . . . . . . : No
    WINS Proxy Enabled. . . . . . . . : No

    Ethernet adapter Local Area Connection:
    Media State . . . . . . . . . . . : Media disconnected
    Description . . . . . . . . . . . : Broadcom 440x 10/100 Integrated Cont
    roller
    Physical Address. . . . . . . . . : 00-1D-09-CB-88-AD

    Ethernet adapter Wireless Network Connection:

    Connection-specific DNS Suffix . :
    Description . . . . . . . . . . . : Dell Wireless 1505 Draft 802.11n WLA
    N Mini-Card
    Physical Address. . . . . . . . . : 00-1E-4C-2F-36-B8
    Dhcp Enabled. . . . . . . . . . . : Yes
    Autoconfiguration Enabled . . . . : Yes
    IP Address. . . . . . . . . . . . : 192.168.8.22
    Subnet Mask . . . . . . . . . . . : 255.255.255.0
    Default Gateway . . . . . . . . . : 192.168.8.1
    DHCP Server . . . . . . . . . . . : 192.168.8.1
    DNS Servers . . . . . . . . . . . : 192.168.8.1
    Lease Obtained. . . . . . . . . . : Saturday, February 12, 2011 3:06:26
    PM
    Lease Expires . . . . . . . . . . : Sunday, February 13, 2011 3:06:26 PM
     
  14. star393

    star393 Private E-2


    i cannot find the fix it for me or fix it myself lines but at the command of netsch i did type itnetsh int ip reset resetlog.txt rebooted and no changes hope that was the manual wh\ay of doing it. Bad instructions from MS
     
  15. handygal

    handygal Sergeant Major

    hrlow2 just reminded me in another thread that sometimes it's not the computer, it's the router. I forget that sometimes when other computers are working.

    I think some routers have security functions in them that recognize your mac but if other things have changed, they block you thinking you might be spoofed or otherwise compromised. That's my theory, I've never bothered to investigate it. Have you reset your connection all the way from the modem?
     
  16. star393

    star393 Private E-2


    i did connect directly to modem bypassing router no luck also my router is giving my computer a ip address.

    my ipconfig has no addresses all zeros

    ran ipconfig/flushdns no luck there also
    i cannot copy my ipconfig and post it like you did just have file how do i send it????????
    my ip is DHCP from comcast

    also i have error when trying to renew ip address = RPC server is unavailable

    I did check router info thats all ok and issuing ip address to my computer but windows willnot allow see your network manager.
     
  17. star393

    star393 Private E-2

    Microsoft Windows XP [Version 5.1.2600]
    (C) Copyright 1985-2001 Microsoft Corp.

    C:\Documents and Settings\Administrator>c:

    C:\Documents and Settings\Administrator>cd c:
    C:\Documents and Settings\Administrator

    C:\Documents and Settings\Administrator>cdc:
    'cdc:' is not recognized as an internal or external command,
    operable program or batch file.

    C:\Documents and Settings\Administrator>cd/c:
    The filename, directory name, or volume label syntax is incorrect.

    C:\Documents and Settings\Administrator>c:

    C:\Documents and Settings\Administrator>cd
    C:\Documents and Settings\Administrator

    C:\Documents and Settings\Administrator>cd c:
    C:\Documents and Settings\Administrator

    C:\Documents and Settings\Administrator>cd\c:
    The filename, directory name, or volume label syntax is incorrect.

    C:\Documents and Settings\Administrator>cd:c
    The filename, directory name, or volume label syntax is incorrect.

    C:\Documents and Settings\Administrator>cd\ c:
    The filename, directory name, or volume label syntax is incorrect.

    C:\Documents and Settings\Administrator>cd/ c:
    The filename, directory name, or volume label syntax is incorrect.

    C:\Documents and Settings\Administrator>cd c:/

    C:\Documents and Settings\Administrator>cd c:
    C:\Documents and Settings\Administrator

    C:\Documents and Settings\Administrator>cd/ c:
    The filename, directory name, or volume label syntax is incorrect.

    C:\Documents and Settings\Administrator>cd?
    'cd?' is not recognized as an internal or external command,
    operable program or batch file.

    C:\Documents and Settings\Administrator>cd ?

    C:\Documents and Settings\Administrator>cd\ c:
    The filename, directory name, or volume label syntax is incorrect.

    C:\Documents and Settings\Administrator>cd/ c:
    The filename, directory name, or volume label syntax is incorrect.

    C:\Documents and Settings\Administrator>c:/
    'c:/' is not recognized as an internal or external command,
    operable program or batch file.

    C:\Documents and Settings\Administrator>c:\
    'c:\' is not recognized as an internal or external command,
    operable program or batch file.

    C:\Documents and Settings\Administrator>help
    For more information on a specific command, type HELP command-name
    ASSOC Displays or modifies file extension associations.
    AT Schedules commands and programs to run on a computer.
    ATTRIB Displays or changes file attributes.
    BREAK Sets or clears extended CTRL+C checking.
    CACLS Displays or modifies access control lists (ACLs) of files.
    CALL Calls one batch program from another.
    CD Displays the name of or changes the current directory.
    CHCP Displays or sets the active code page number.
    CHDIR Displays the name of or changes the current directory.
    CHKDSK Checks a disk and displays a status report.
    CHKNTFS Displays or modifies the checking of disk at boot time.
    CLS Clears the screen.
    CMD Starts a new instance of the Windows command interpreter.
    COLOR Sets the default console foreground and background colors.
    COMP Compares the contents of two files or sets of files.
    COMPACT Displays or alters the compression of files on NTFS partitions.
    CONVERT Converts FAT volumes to NTFS. You cannot convert the
    current drive.
    COPY Copies one or more files to another location.
    DATE Displays or sets the date.
    DEL Deletes one or more files.
    DIR Displays a list of files and subdirectories in a directory.
    DISKCOMP Compares the contents of two floppy disks.
    DISKCOPY Copies the contents of one floppy disk to another.
    DOSKEY Edits command lines, recalls Windows commands, and creates macros.
    ECHO Displays messages, or turns command echoing on or off.
    ENDLOCAL Ends localization of environment changes in a batch file.
    ERASE Deletes one or more files.
    EXIT Quits the CMD.EXE program (command interpreter).
    FC Compares two files or sets of files, and displays the differences
    between them.
    FIND Searches for a text string in a file or files.
    FINDSTR Searches for strings in files.
    FOR Runs a specified command for each file in a set of files.
    FORMAT Formats a disk for use with Windows.
    FTYPE Displays or modifies file types used in file extension associations.
    GOTO Directs the Windows command interpreter to a labeled line in a
    batch program.
    GRAFTABL Enables Windows to display an extended character set in graphics
    mode.
    HELP Provides Help information for Windows commands.
    IF Performs conditional processing in batch programs.
    LABEL Creates, changes, or deletes the volume label of a disk.
    MD Creates a directory.
    MKDIR Creates a directory.
    MODE Configures a system device.
    MORE Displays output one screen at a time.
    MOVE Moves one or more files from one directory to another directory.
    PATH Displays or sets a search path for executable files.
    PAUSE Suspends processing of a batch file and displays a message.
    POPD Restores the previous value of the current directory saved by PUSHD.
    PRINT Prints a text file.
    PROMPT Changes the Windows command prompt.
    PUSHD Saves the current directory then changes it.
    RD Removes a directory.
    RECOVER Recovers readable information from a bad or defective disk.
    REM Records comments (remarks) in batch files or CONFIG.SYS.
    REN Renames a file or files.
    RENAME Renames a file or files.
    REPLACE Replaces files.
    RMDIR Removes a directory.
    SET Displays, sets, or removes Windows environment variables.
    SETLOCAL Begins localization of environment changes in a batch file.
    SHIFT Shifts the position of replaceable parameters in batch files.
    SORT Sorts input.
    START Starts a separate window to run a specified program or command.
    SUBST Associates a path with a drive letter.
    TIME Displays or sets the system time.
    TITLE Sets the window title for a CMD.EXE session.
    TREE Graphically displays the directory structure of a drive or path.
    TYPE Displays the contents of a text file.
    VER Displays the Windows version.
    VERIFY Tells Windows whether to verify that your files are written
    correctly to a disk.
    VOL Displays a disk volume label and serial number.
    XCOPY Copies files and directory trees.

    C:\Documents and Settings\Administrator>cdir
    'cdir' is not recognized as an internal or external command,
    operable program or batch file.

    C:\Documents and Settings\Administrator>c:

    C:\Documents and Settings\Administrator>cd /c:
    The filename, directory name, or volume label syntax is incorrect.

    C:\Documents and Settings\Administrator>cd/ c:
    The filename, directory name, or volume label syntax is incorrect.

    C:\Documents and Settings\Administrator>cd/ c
    The system cannot find the path specified.

    C:\Documents and Settings\Administrator>cd:
    The filename, directory name, or volume label syntax is incorrect.

    C:\Documents and Settings\Administrator>cd c:
    C:\Documents and Settings\Administrator\.

    C:\Documents and Settings\Administrator>cd\ c:
    The filename, directory name, or volume label syntax is incorrect.

    C:\Documents and Settings\Administrator>c:/
    'c:/' is not recognized as an internal or external command,
    operable program or batch file.

    C:\Documents and Settings\Administrator>c:\
    'c:\' is not recognized as an internal or external command,
    operable program or batch file.

    C:\Documents and Settings\Administrator>cd /c:
    The filename, directory name, or volume label syntax is incorrect.

    C:\Documents and Settings\Administrator>cd\ c:
    The filename, directory name, or volume label syntax is incorrect.

    C:\Documents and Settings\Administrator>cd\c:
    The filename, directory name, or volume label syntax is incorrect.

    C:\Documents and Settings\Administrator>cd windows

    C:\Documents and Settings\Administrator\WINDOWS>ipconfig

    Windows IP Configuration


    Ethernet adapter Local Area Connection 11:

    Connection-specific DNS Suffix . :
    IP Address. . . . . . . . . . . . : 0.0.0.0
    Subnet Mask . . . . . . . . . . . : 0.0.0.0
    Default Gateway . . . . . . . . . :

    Tunnel adapter Teredo Tunneling Pseudo-Interface:

    Connection-specific DNS Suffix . :
    IP Address. . . . . . . . . . . . : fe80::ffff:ffff:fffd%4
    Default Gateway . . . . . . . . . :

    C:\Documents and Settings\Administrator\WINDOWS>
     
  18. star393

    star393 Private E-2


    Thanks for working with me
     
  19. Colemanguy

    Colemanguy MajorGeek

    what was the netsh qc command supposed to do? Who told you to run that? Google gave me very rough ideas that its used to reset some of the dhcp stuff. netsh winsock reset command only works if its windows xp sp2 or greater. The bigger concern to me is dispearing devices and rpc errors, which indicate a damaged os, I would first recommend your put in your xp cd, and at the run box type, sfc /scannow which stands for system file checker, and start with that. Are programs randomly crashing and stuff or other then the no internet is the system working normaly?
     
  20. star393

    star393 Private E-2

    netsh microsoft fix it 50199 to reset tcp\ip

    that disappearing act has stop after i ran a malware program and registry checker program

    computer and programs are all stable and run normal

    ill try the scannow is that like the scandisk program?????
    ive only been running winxp pro for ayear now clean install


    Thanks for repleys
     
Thread Status:
Not open for further replies.

Share This Page

MajorGeeks.Com Menu

MajorGeeks.Com \ All In One Tweaks \ Android \ Anti-Malware \ Anti-Virus \ Appearance \ Backup \ Browsers \ CD\DVD\Blu-Ray \ Covert Ops \ Drive Utilities \ Drivers \ Graphics \ Internet Tools \ Multimedia \ Networking \ Office Tools \ NEW! PC Games \ System Tools \ Macintosh \ Demonews.Com \ Top Downloads

MajorGeeks.Com \ News (Tech) \ Off Base (Other Websites News) \ Way Off Base (Offbeat Stories and Pics)

Social: Facebook \ YouTube \ Twitter \ Tumblr \ Pintrest \ RSS Feeds